Exsenco U.S Contact For Santest

GYMT

 

Photograph 2
The GYMT probe and the GYMTC controller are the compact sensor which is born by making possible limit circuit constitution simple. With compact conversion low cost conversion is actualized, reliability has improved furthermore with the probe protection standard IP-67 design. In addition connector type made the using good quality which surpasses to former cable gland type possible. 0 - 10V or it can obtain the analog signal 4 - 20mA with the combination of the GYMT probe and the GYMTC controller.
 2
2
 
2

Specifications
2
Precision Linearity Below TYP ±0.05%FS
Resolution Below 0.01%FS
Repeatability Below ±0.01%FS
Temperature characteristic ±50ppm FS/℃ (probe)
±80ppm FS/℃ (controller)
Output Voltage output 0 - 10VDC or 10 - 0VDC
Load current Max 5mA, load resistance Min 2kΩ
Electric current output 4 - 20mA or 20 - 4mA
Load resistance Max 500Ω
Frequency characteristic Scanning frequency 1kHz (standard)
Power source and consumed electric current ±15VDC type +15V±5% below 100mA
　　　　　　　-15V±5% below 50mA
+24VDC type +24V±5% below 200mA
+12VDC type +12V±5% below 400mA
Environmental characteristic Resisting pressure 35MPa (probe rod)
Category temperature range Probe -5℃ - +60℃
Controller 0℃ - +60℃
Storage temperature range -40℃ - +80℃
Resistance swing 6G (or 40Hz 2mmPP)
Shock resistant 50G (2msec)
Protective standard IP 67 (probe) (note)
Cable 1.5m (standard) (option Max10m)
2

* The above-mentioned precision is applied to the sensor above effective stroke 300mm.
Note) protective standard IP67 withstands the use 30 minutes to the depth of water 1m. (You cannot use for the use which it submerges continually) and, connector type waterproof efficiency is shown in fitting state of the connector.
2

Type Variations
2
2  
GYMT-□□□□-□-□□
1 Effective stroke
2 300.500.700.1000.1500.2000 (max2000mm)
2 Installation screw
2 J8: M20×P1 (standard) L8: M16×2.0 N: M18×P1.5 (rod diameter φ10) U: 3/4-16UNF (rod diameter φ10)
3 Cable removal
2 G*: [piguteiru] type (standard) (* cable length (m): Standard 1.5) CN: Connector type
 
GYMTC-11-□-□□□□-□□□-□
1 Output
2 A: 0 - 10V B: 4 - 20mA C: In addition (bipolar and the like)
2 Effective stroke
2 300.500.700.1000.1500.2000
3 Supply power source
2 15W: ±15VDC 24S: +24VDC 12S: +12VDC
4 Operational direction (to rod point when moving)
2 D: Increase operation R: Decrease operation
 
CLMT-□□-□
1 Cable length (m)
2
2 Connector form
2 S: Straight type L: Angle type
2
2
2
* Please choose the magnet from No.φ, No.2P and No.11 etc.
* As for output fine control of zero/full scale points it is possible to do with the controller front trimmer. (Adjustment range: ±3%FS)
* The cable please use at the length which you indicate.
Extension and cutting of the cable need readjustment.
Cable it is possible to install the Terminal Block and the connector etc on the middle.
2

External Dimensions Drawing
2
2 ●GYMT probe
2
2 Material probe head: SUS304 probe rod: SUS304
GYMT probe <Cable gland type (standard)>
 <Cable gland type (standard)>
GYMT probe <Connector type (option)>
 <Connector type (option)>
　Connector type
　XS2C-D4S1 (Omuron make)
GYMT probe <Angle connector type (option)> <Angle connector type (option)>
　Connector type
　XS2C-D4S2 (Omuron make)
2
2 ●GYMTC controller
GYMTC controller 2
2 2 2 2 2
2

Options
2
It can produce the effective stroke of the probe at the optional length of 30mm - 2000mm.
At option it can produce the cable at the optional length to 10m. In order (however, effective stroke (m) × cable length (to become m) ≦10, please order. )
The connector can choose also angle type.
Output bipolar and reversal output etc is possible.